| 淡江大學 |
2008-05 |
The analysis of forming limit in re-penetration process of the hole-flanging of sheet metal
|
Li, Ching-Lun; Huang, You-Min; Tsai, Yi-Wei |
| 國立臺灣科技大學 |
2008 |
Analysis of forming limits in metal forming processes
|
Huang, You-Min ; Tsai, Yi-Wei ; Li, Ching-Lun |
| 國立臺灣科技大學 |
2008 |
The analysis of forming limit in re-penetration process of the hole-flanging of sheet metal
|
Li, Ching-Lun ; Huang, You-Min ; Tsai, Yi-Wei |
| 淡江大學 |
2007-10 |
Analysis of Forming Limits in Metal Forming Processes
|
Li, Ching-Lun; Huang, You-Min; Tsai, Yi-Wei |
| 淡江大學 |
2007-10 |
The Analysis of Forming Limit in Re-penetration Process of the Hole-Flanging of Sheet Metal
|
Li, Ching-Lun; Huang, You-Min; Tsai, Yi-Wei |
| 國立臺灣科技大學 |
2007 |
An Elasto-Plastic Finite Element Simulation of the UO-Tube Processes of Sheet Metal
|
Chen, T. C. ; Huang, You-Min |
| 國立臺灣科技大學 |
2007 |
Development of Stereolithography Simulation Process based on the Dynamic Finite Element Method
|
Huang, You-Min ; Jiang, C. P. |
| 國立臺灣科技大學 |
2007 |
Numerical Analysis for Bifurcation Fracture of Sheet Metal Forming
|
Huang, You-Min ; Kuriyama, S. |
| 國立臺灣科技大學 |
2006 |
A Study of Optimum Blank in the Deep Drawing Process of Square Cup with Flange by using Adaptive Network Fuzzy Inference System
|
Li, C. L. ; Huang, You-Min ; Tsai, Y. W. |
| 國立臺灣科技大學 |
2006 |
An Elasto-Plastic Finite Element Analysis of the Hat-Type Drawing Process of Sheet Metal
|
Chen, T. C. ; Huang, You-Min |
| 國立臺灣科技大學 |
2006 |
Compensation of Distortion in the Bottom Exposure of Stereolithography Process
|
Huang, You-Min ; Lan, H. Y. |
| 國立臺灣科技大學 |
2006 |
Dynamic Finite Element Analysis of Photopolymerization in Stereolithography
|
Jiang, C. P. ; Huang, You-Min ; Liu, C. H. |
| 國立臺灣科技大學 |
2006 |
Path Planning Effect for the Accuracy of Rapid Prototyping System
|
Huang, You-Min ; Lan, H. Y. |
| 淡江大學 |
2005-11 |
A Study of Optimum Blank in the Deep Drawing Process of Square Cup with Flange by Using Adaptive Network Fuzzy Inference System
|
Li, Ching-Lun; Huang, You-Min; Tsai, Yi-Wei |
| 國立臺灣科技大學 |
2005 |
CAD/CAE/CAM Integration for Increasing the Accuracy of Mask Rapid Prototyping System
|
Huang, You-Min ; Lan, H. Y. |
| 國立臺灣科技大學 |
2005 |
Development of Masked Photo-polymerization Rapid Prototyping System using Liquid Crystal Display Panel
|
Jiang, Cho-Pei; Jeng, Jeng-Ywan ; Huang, You-Min ; Tsai, Ming-Jong |
| 國立臺灣科技大學 |
2005 |
Dynamic Reverse Compensation to Increase the Accuracy of the Rapid Prototyping System
|
Huang, You-Min ; Lan, H. Y. |
| 國立臺灣科技大學 |
2005 |
Influence of Blank Profiles on the V-die Bending Camber Process of Sheet Metal
|
Huang, You-Min ; Chen, T.C. |
| 國立臺灣科技大學 |
2005 |
On Line Monitoring of Platform Ascending Rapid Prototyping System
|
Huang, You-Min ; Jiang, C. P. |
| 國立臺灣科技大學 |
2004 |
An Effect of Material Parameters on the Camber Behavior
|
Huang, You-Min ; Chen, T.C. |
| 國立臺灣科技大學 |
2004 |
An Influence of Tool Profiles on the V-bending Process of Sheet Metal
|
Huang, You-Min ; Chen, T.C. |
| 國立臺灣科技大學 |
2004 |
Fundamental Study and Theoretical Analysis in the Constrain-Surface Stereolithography System
|
Huang, You-Min; Kuriyama, S. ; Jiang, C. P. |
| 國立勤益科技大學 |
2003-09 |
An elasto-plastic finite-element analysis of sheet metal camber process
|
Huang, You-Min;Chen, Tsung-Chia |
| 國立臺灣科技大學 |
2003 |
An Elasto-Plastic Finite Element Analysis of Sheet Metal Camber Process
|
Huang, You-Min ; Chen, T. C. |
| 國立臺灣科技大學 |
2003 |
Curl distortion analysis during photopolymerization of stereolithography using dynamic finite element
|
Huang, You-Min ; Jiang, C. P. |
