|
"tsai yi wei"的相关文件
显示项目 1-12 / 12 (共1页)
1
每页显示[10|25|50]项目
| 臺大學術典藏 |
2022-02-21T23:30:59Z |
Face and Head Detection for Back View Cases Using Gradient Features and Learning Architecture
|
Tsai, Yi Wei; JIAN-JIUN DING; Lu, De Yan |
| 臺大學術典藏 |
2022-02-21T23:30:58Z |
Pixelwise Image Sharpness Based on the Weighted Response Ratios of Short and Long Edge Detectors
|
JIAN-JIUN DING; Tsai, Yi Wei |
| 臺大學術典藏 |
2021-07-15T05:32:50Z |
Regulated Li Electrodeposition Behavior through Mesoporous Silica Thin Film in Anode-Free Lithium Metal Batteries
|
Lo, Chang An; Chang, Chiao Chun; Tsai, Yi Wei; Jiang, Shi Kai; Hwang, Bing Joe; CHUNG-YUAN MOU; HENG-LIANG WU |
| 國立臺灣師範大學 |
2019-09-03T12:28:28Z |
台灣中學生之英語閱讀測驗做答策略研究
|
魏采誼; Tsai-Yi, Wei |
| 國立交通大學 |
2015-12-02T02:59:09Z |
Single-mode selection for hard x-ray cavity resonance
|
Tsai, Yi-Wei; Chang, Ying-Yi; Wu, Yu-Hsin; Liu, Wen-Chung; Peng, Chou-Chi; Hsieh, Wen-Feng; Chang, Shih-Lin |
| 淡江大學 |
2008-05 |
The analysis of forming limit in re-penetration process of the hole-flanging of sheet metal
|
Li, Ching-Lun; Huang, You-Min; Tsai, Yi-Wei |
| 國立臺灣科技大學 |
2008 |
Analysis of forming limits in metal forming processes
|
Huang, You-Min ; Tsai, Yi-Wei ; Li, Ching-Lun |
| 國立臺灣科技大學 |
2008 |
The analysis of forming limit in re-penetration process of the hole-flanging of sheet metal
|
Li, Ching-Lun ; Huang, You-Min ; Tsai, Yi-Wei |
| 淡江大學 |
2007-10 |
Analysis of Forming Limits in Metal Forming Processes
|
Li, Ching-Lun; Huang, You-Min; Tsai, Yi-Wei |
| 淡江大學 |
2007-10 |
The Analysis of Forming Limit in Re-penetration Process of the Hole-Flanging of Sheet Metal
|
Li, Ching-Lun; Huang, You-Min; Tsai, Yi-Wei |
| 淡江大學 |
2005-12 |
方杯深引伸成形極限之最佳化料片之研究
|
李經綸; Li, Ching-Lun; 蔡毅瑋; Tsai, Yi-Wei; 李建輝; Li, Chien-Hui;于國光; Yu, Kuo-Kuang |
| 淡江大學 |
2005-11 |
A Study of Optimum Blank in the Deep Drawing Process of Square Cup with Flange by Using Adaptive Network Fuzzy Inference System
|
Li, Ching-Lun; Huang, You-Min; Tsai, Yi-Wei |
显示项目 1-12 / 12 (共1页)
1
每页显示[10|25|50]项目
|
